Elevator traffic analysis helps determine whether a building’s elevator system can handle its expected passenger demand while meeting service targets for handling capacity, interval, and waiting time. The results inform decisions about elevator quantity, rated capacity, speed, zoning, and dispatching strategy.
For building developers, architects, consultants, and procurement teams, the challenge is not simply to transport more passengers. The selected configuration must balance traffic demand, passenger experience, shaft space, installation cost, and long-term operating requirements.
A configuration may meet its five-minute handling capacity target but still produce an interval that exceeds the project’s target. Understanding this distinction is essential when comparing elevator proposals or evaluating whether an existing system needs modification.
What Is Elevator Traffic Analysis?
Elevator traffic analysis evaluates the expected performance of an elevator group under defined building occupancy, passenger-flow, and operating conditions.
It supports two related activities.
- Traffic planning evaluates proposed elevator configurations during building design, modernization, or system replacement.
- Traffic management coordinates operating elevators by assigning calls according to factors such as car position, direction, registered destinations, and current load.
Traffic planning estimates whether a proposed configuration can meet the building’s service requirements. Traffic management determines how the installed system responds to changing demand.
For example, increasing the number of elevators may reduce the theoretical interval, but it also consumes additional shaft space and increases equipment costs. Revising service zones or reducing unnecessary stops may offer an alternative, provided the building layout and passenger destinations support the change.
The appropriate solution therefore depends on both the calculated traffic demand and the physical and operational constraints of the building.
Key Elevator Traffic Performance Metrics
Handling Capacity
Handling capacity is the number of passengers an elevator group can transport during a specified period. For conventional office-building up-peak analysis, it is commonly expressed as passengers per five minutes or as a percentage of the relevant building population.
For example, transporting 150 passengers in five minutes represents approximately 9.8% of an occupied population of 1,536 people.
The denominator matters. A percentage calculated from the total design population will differ from one calculated using expected daily attendance.
Handling capacity also depends on the average number of passengers carried per trip, not merely the rated capacity of each car. A calculation that assumes every trip operates at the maximum permitted load may overstate practical performance.

Interval
Interval is the average time between successive elevator departures from or arrivals at a reference floor, commonly the main entrance during up-peak analysis.
For a simplified model in which all elevators have the same round-trip time, interval can be estimated as
[I=\frac{RTT}{N}]
Where:
- (I) is the estimated interval in seconds.
- (RTT) is the round-trip time in seconds.
- (N) is the number of elevators in the group.
Interval is a group-level service indicator. A shorter interval generally means that elevator service is offered more frequently at the reference floor, but it does not guarantee that every passenger will experience a short wait.
Waiting Time
Waiting time is the time between a passenger registering a hall call and boarding an elevator.
It depends on elevator availability, passenger arrival patterns, dispatching logic, queue formation, and the distribution of destinations. Average waiting time and maximum or percentile waiting times describe different aspects of service.
A traffic report should state which waiting-time measure it evaluates. An acceptable average can conceal long waits during concentrated demand, particularly when certain floors or passenger groups generate disproportionate traffic.
Round-Trip Time
Round-trip time (RTT) estimates the time required for an elevator to complete a defined service cycle and return to its reference floor.
In a simplified up-peak model, the cycle includes boarding at the entrance, upward travel with intermediate stops, reaching the highest reversal floor, and returning to the entrance.
RTT is influenced by:
- The highest floor reached during the trip
- Travel time between floors
- The number of intermediate stops
- Door operation and stopping losses
- Passenger boarding and exiting time
- Additional delays included in the selected calculation method
Rated speed alone cannot determine RTT. An elevator may not reach rated speed during a short trip, and frequent stops can make door operation and passenger transfer time significant components of the cycle.
Probable Number of Stops and Highest Reversal Floor
The probable number of stops estimates how many distinct destination floors an elevator will serve during a trip. The highest reversal floor is the highest floor reached before the elevator returns to the entrance.
Both depend on passenger destinations and floor population distribution.
A building with a relatively uniform population may have a different stop pattern from one with concentrated demand on a few floors. The same total population can therefore produce different RTT estimates.
These variables should be based on the building’s expected use and stated traffic assumptions rather than selected solely from the number of floors.
How to Calculate Elevator Traffic Performance
Preliminary elevator traffic calculations help screen candidate configurations before more detailed analysis is undertaken. Their reliability depends on the quality of the input data and whether the selected model represents the building’s actual passenger movements.
Step 1. Collect Building and Passenger Data
Establish the following information before calculating performance.
- Total design population and expected attendance
- Population distribution by floor
- Number of floors, floor-to-floor heights, and entrances
- Elevator quantity, rated capacity, and rated speed
- Door opening, closing, and dwell times
- Passenger boarding and exiting assumptions
- Expected peak traffic patterns
- Required handling capacity, interval, and waiting-time targets
Floor-level population is especially important in buildings with restaurants, conference facilities, healthcare functions, or other areas that generate concentrated demand.
Where reliable floor-level data are unavailable, the report should identify the assumed distribution and explain how that assumption affects the results.
Step 2. Estimate the Probable Number of Stops
For a simplified model in which passengers independently select destinations with equal probability across the available floors, the expected number of distinct stops can be estimated using
[S_p=F\left[1-\left(1-\frac{1}{F}\right)^M\right]]
Where:
- (S_p) is the expected number of stops.
- (F) is the number of available destination floors above the entrance.
- (M) is the number of passengers boarding at the entrance.
The formula estimates how many different floors are likely to be selected by the passengers in one trip.
For example, if 16 passengers select destinations among 10 floors, the expected number of distinct destination floors is
[\begin{aligned}
S_p&=10\left[1-\left(1-\frac{1}{10}\right)^{16}\right]\
&=10(1-0.9^{16})\
&\approx8.15
\end{aligned}]
The result is an expected value, not a prediction that every trip will stop at exactly 8.15 floors.
This estimate assumes equal destination probabilities. If certain floors contain substantially more occupants, the model may not accurately represent the actual stopping pattern.
Step 3. Estimate Round-Trip Time
A simplified RTT model can separate travel time, stopping losses, and passenger transfer time:
[RTT=2Ht_f+(S+1)t_s+2Mt_p]
Where:
- (H) is the estimated highest reversal floor, expressed as the number of floor intervals above the entrance.
- (t_f) is the effective travel time per floor interval under the assumed motion profile.
- (S) is the expected number of intermediate stops.
- (t_s) is the additional time allocated to each modeled stop, excluding passenger transfer time.
- (M) is the average number of passengers boarding at the entrance.
- (t_p) is the assumed boarding or exiting time per passenger.
The factor of two in the travel term represents upward and return travel. The term (S+1) includes the intermediate stops and the upper reversal stop in this simplified model. The passenger-transfer term represents boarding and exiting time.
These terms must be defined so that door operation, travel time, and passenger transfer are not counted twice. The formula is a simplified illustrative model, not a universal RTT equation for every elevator configuration.
Step 4. Calculate Interval and Five-Minute Handling Capacity
For a group of (N) elevators with a common estimated RTT,
[I=\frac{RTT}{N}]
Estimated five-minute handling capacity is
[HC_5=\frac{300NP}{RTT}]
Where:
- (HC_5) is the estimated number of passengers transported in five minutes.
- (300) is the number of seconds in five minutes.
- (N) is the number of elevators.
- (P) is the average number of passengers carried per completed cycle.
- (RTT) is round-trip time in seconds.
If the rated capacity is (C) and the assumed average loading factor is (L), expressed as a decimal,
[P=LC]
For example, an assumed loading factor of 80% gives (P=0.8C). This is a modeling assumption rather than a universal requirement. The factor should not be applied again if (P) already represents the average passenger load.
These equations estimate performance under the specified assumptions. They do not independently predict actual waiting-time distributions or guarantee performance under every traffic pattern.
Step 5. Compare Alternative Elevator Configurations
Consider an illustrative office building with the following assumptions.
| Input | Assumed value |
|---|---|
| Floors above the entrance | 10 |
| Floor-to-floor height | 3.6 m |
| Number of available destination floors, (F) | 10 |
| Average passengers per trip, (M=P) | 16 |
| Rated capacity per elevator | 20 passengers |
| Assumed average loading factor | 80% |
| Estimated highest reversal floor, (H) | 9.2 |
| Expected number of stops, (S) | 8.15 |
| Effective travel time per floor interval, (t_f) | 4.5 s |
| Additional time per modeled stop, (t_s) | 7.5 s |
| Boarding or exiting time per passenger, (t_p) | 1.0 s |
| Target handling capacity | 150 passengers/5 min |
| Target interval | 32 s |
The values are hypothetical inputs chosen to demonstrate the calculation method. The highest reversal floor and effective travel time are assumptions for this example, not values automatically derived from rated speed or the stop-probability formula.
Calculate RTT
Using the simplified model,
[RTT=2Ht_f+(S+1)t_s+2Mt_p]
Substituting the assumed values,
[\begin{aligned}
RTT&=2(9.2)(4.5)\
&\quad +(8.15+1)(7.5)\
&\quad +2(16)(1.0)\
&=82.8+68.625+32\
&=183.425\text{ s}
\end{aligned}]
The estimated RTT is therefore approximately 183.4 seconds.
The travel term accounts for upward and return travel. The stop-time term accounts for additional losses at the modeled stops, while the final term accounts for passenger boarding and exiting. These terms are assumed to be separate and non-overlapping.
Actual RTT may differ because of the elevator’s acceleration and deceleration profile, floor population distribution, door behavior, dispatching, and delays not included in the simplified model.
Compare Five and Six Elevators
For five elevators,
[I_5=\frac{183.425}{5}\approx36.7\text{ s}]
[HC_{5,5}=\frac{300\times5\times16}{183.425}
\approx131\text{ passengers}]
For six elevators, assuming the same RTT and average passenger load per car,
[I_6=\frac{183.425}{6}\approx30.6\text{ s}]
[HC_{5,6}=\frac{300\times6\times16}{183.425}
\approx157\text{ passengers}]
| Performance measure | Five elevators | Six elevators |
|---|---|---|
| Assumed RTT | 183.4 s | 183.4 s |
| Estimated interval | 36.7 s | 30.6 s |
| Five-minute handling capacity | 131 passengers | 157 passengers |
| Meets 150-passenger capacity target | No | Yes |
| Meets 32-second interval target | No | Yes |
Under these assumptions, five elevators do not meet either target. Six elevators meet both modeled targets.
This comparison demonstrates how handling capacity and interval can be evaluated together. It does not establish that six elevators are the optimal solution for a real building.
The calculation assumes that adding an elevator does not change RTT or the average passenger load per trip. In practice, the additional car may alter dispatching, passenger distribution, and operating conditions. A final decision must also account for shaft space, capital expenditure, maintenance requirements, and the required service margin.
How Building Use Changes Elevator Traffic Patterns
The appropriate traffic model depends on the building’s dominant passenger movements. An up-peak calculation alone may not represent service requirements where traffic is substantial in both directions or between upper floors.
Up-Peak Traffic
Up-peak traffic commonly occurs during morning arrivals in office buildings, when passengers enter at the main entrance and travel to upper floors.
The analysis should consider arrival rates, passenger loading, floor distribution, and the number of intermediate stops. This model is useful for evaluating concentrated upward demand but does not establish performance during other periods.
Down-Peak and Interfloor Traffic
Down-peak traffic occurs when passengers travel from upper floors toward an exit floor. Interfloor traffic involves movement between upper floors rather than mainly between the entrance and upper levels.
Residential buildings, hotels, hospitals, universities, and mixed-use developments may experience different combinations of these patterns. The analysis should reflect the expected distribution of trips rather than applying a single up-peak assumption to every building.
Building-Specific Planning Considerations
| Building type | Key traffic consideration | Planning implication |
|---|---|---|
| Office | Concentrated arrival and departure periods | Evaluate up-peak, down-peak, and lunch traffic |
| Residential | Morning departures and evening returns | Consider demand in both directions |
| Hotel | Guests, luggage, and service activity | Assess passenger distribution and service separation |
| Hospital | Patients, staff, visitors, and equipment | Consider distinct transport functions and operating priorities |
| Mixed-use | Different populations and schedules | Evaluate separate or coordinated service groups |
These characteristics determine which scenarios should be modeled. They do not establish a fixed elevator quantity without project-specific calculations.
For healthcare projects, medical passenger elevators can be reviewed in relation to passenger transport requirements, cabin dimensions, and door arrangements.
Calculation vs. Elevator Traffic Simulation
When Preliminary Calculation Is Appropriate
Simplified calculations are useful for initial screening when the building has a clear dominant traffic pattern, floor populations are reasonably represented by the assumptions, and the purpose is to compare preliminary configurations.
They provide a way to estimate basic handling capacity, interval, and RTT before more detailed analysis is undertaken.
When Simulation Is More Appropriate
More detailed traffic simulation should be considered when the assumptions of the simplified model are unlikely to represent the building adequately.
Typical triggers include:
- Uneven floor populations or concentrated destinations
- Significant two-way or interfloor traffic
- Multiple entrances or transfer floors
- Several elevator groups serving different zones
- Destination control or complex dispatching strategies
- Double-deck elevators or other specialized configurations
- Modernization projects with restricted shaft space and existing equipment
- Performance targets that require analysis of waiting-time distributions rather than average interval alone
Simulation can evaluate multiple operating scenarios, but its reliability depends on input data, model assumptions, and whether the modeled operating logic reflects the proposed installation.
A simulation report should identify the population, passenger arrival patterns, destination distribution, elevator specifications, door-operation assumptions, and performance indicators used. Results without these details are difficult to reproduce or compare.
How to Compare Elevator Supplier Proposals
Comparing proposals requires more than checking the number of elevators or their rated speed. Each proposal should be evaluated against the same building data, traffic assumptions, and service targets.
Use a Consistent Comparison Framework
| Comparison item | What to verify | Why it matters |
|---|---|---|
| Design population | Total population and expected attendance | Different population assumptions change estimated demand |
| Floor distribution | Occupancy and destination patterns | Affects stops, reversal floor, and RTT |
| Passenger loading | Average passengers per trip and loading factor | Directly affects estimated handling capacity |
| Travel assumptions | Floor heights, motion profile, and rated speed | Determines travel time and stopping behavior |
| Door operation | Opening, closing, dwell, and transfer assumptions | Can materially affect RTT |
| Elevator quantity | Number of cars available during normal operation | Affects interval and group capacity |
| Service zones | Floors served by each elevator group | Affects travel distances, transfers, and stop patterns |
| Performance measures | Capacity, interval, and waiting-time targets | Prevents one favorable indicator from masking another |
| Model method | Simplified calculation or simulation | Determines what the results can reliably establish |
| Space and cost | Shaft requirements, installation cost, and lifecycle cost | Connects modeled performance to project feasibility |
If two proposals produce different results, compare their inputs before concluding that one configuration is better. A proposal that assumes shorter door times or higher average passenger loading may predict greater handling capacity without representing a genuinely superior design.
The report should explain not only which configuration meets the targets, but also which assumptions drive the result and whether those assumptions are supported by the intended building operation.
How Elevator Configuration Affects Traffic Performance
Elevator Quantity and Rated Capacity
Adding elevators can shorten the estimated interval and increase group handling capacity when other assumptions remain comparable. Increasing car capacity can also increase the number of passengers carried per trip.
The trade-off is additional equipment, shaft space, installation cost, and maintenance obligations. The preferred configuration depends on the required service level and the building’s physical constraints.
For projects evaluating commercial applications, commercial passenger elevators provide a relevant starting point for reviewing available system categories.
Rated Speed and Acceleration
Higher rated speed can reduce travel time over long journeys, but the benefit is limited when trips are short or involve frequent stops.
Acceleration, deceleration, door operation, and passenger transfers may remain significant components of RTT. The analysis should therefore evaluate the complete operating cycle rather than assume that a higher rated speed produces a proportional reduction in waiting time.
For buildings with long travel distances, high-speed elevators may be relevant when reviewing equipment options. Suitability still depends on building height, travel distances, passenger demand, and the overall traffic plan.
Zoning and Destination Control
Zoning assigns elevator groups to specific floor ranges. It can reduce unnecessary travel when passenger destinations align with the zones, but it may also introduce transfers or restrict direct access.
Destination control registers passenger destinations before boarding and assigns passengers to elevators according to the dispatching strategy. Grouping passengers traveling to similar floors can reduce intermediate stops when the building layout and destination distribution support the approach.
Neither strategy automatically compensates for insufficient capacity or an unsuitable building layout. The benefits must be evaluated against the full passenger journey, including transfers and access to the destination floor.
Double-Deck Elevators
Double-deck elevators use two vertically arranged cabins to serve two floors at a suitably designed landing arrangement. They may increase throughput in buildings with concentrated shuttle traffic.
Their suitability depends on entrance arrangements, floor heights, passenger distribution, and traffic direction. Irregular floor heights or substantial interfloor traffic may complicate their use.
The decision should account for passenger circulation and the relationship between the elevator arrangement and the building’s floor plan rather than focusing only on nominal capacity.
High-Rise Buildings and Transfer Floors
Tall buildings may use shuttle elevators to transport passengers to a sky lobby, followed by local elevators serving designated floor zones.
This arrangement can reduce long-distance travel within local groups, but transfer time and lobby capacity become part of the passenger journey. The analysis should evaluate end-to-end service rather than only the RTT of individual elevator groups.
Core-space constraints are also important. Elevator shaft systems can be reviewed alongside the proposed building layout, with final shaft dimensions and arrangements coordinated with the project design.
Elevator Modernization, Maintenance, and Lifecycle Considerations
Existing buildings introduce constraints that may not appear in a new-build calculation. Shaft dimensions, pit depth, overhead clearance, existing entrances, electrical capacity, and the condition of installed equipment can limit the available configurations.
A modernization assessment should therefore separate traffic requirements from physical feasibility.
First, determine whether the existing system fails because of insufficient handling capacity, excessive interval, poor dispatching, or a mismatch between the original design and current occupancy. These causes may require different solutions.
Second, compare possible interventions. Depending on the building, options may include revised dispatching, changes to service zones, equipment modernization, or additional elevator capacity where the structure permits it.
Third, assess lifecycle implications. A configuration that meets the initial traffic target may still be unsuitable if maintenance access is difficult, critical components are difficult to replace, or future modernization would require extensive structural work.
The evaluation should consider:
- Initial equipment and installation cost
- Energy consumption under expected operating conditions
- Maintenance access and service requirements
- Spare-parts availability and component compatibility
- Expected operating availability
- Future changes in building population and use
- Structural and space constraints affecting future modifications
These factors should be compared using project-specific data rather than unsupported assumptions about savings or service life.
For existing buildings, elevator control systems may be relevant when reviewing control-system options. Compatibility and expected performance must be confirmed against the installed equipment and the proposed modernization scope.
Common Elevator Traffic Analysis Errors
Unrealistic Door and Transfer Times
Underestimating door operation or passenger transfer time reduces calculated RTT and inflates estimated handling capacity. Time assumptions should reflect the proposed operating arrangement and should not overlap with other terms in the calculation.
Overly Optimistic Passenger Loading
Rated capacity is not the same as average passenger loading. Crowding, luggage, accessibility requirements, and passenger behavior can reduce the number of people boarding each trip.
Reports should distinguish rated capacity from the assumed average load and explain the basis for the loading factor.
Incorrect Population Distribution
A total population figure does not describe every traffic pattern. Concentrated demand on particular floors can change the probable number of stops, reversal floor, and service cycle.
Floor-level occupancy should be used where reliable data are available. Otherwise, the report should disclose the assumed distribution and identify its effect on the results.
Ignoring Short-Distance Travel
An elevator may not reach rated speed during a one-floor or two-floor journey. Calculations that assume rated-speed travel throughout these trips can underestimate travel time.
This is especially important in buildings with many short journeys or frequent stops, where acceleration and deceleration make up a larger proportion of each trip.
Evaluating Only One Traffic Pattern
An up-peak calculation does not establish performance during down-peak, lunch, or interfloor traffic. Select scenarios based on building use and the passenger movements most likely to constrain service.
Comparing Inconsistent Proposals
Different assumptions about attendance, passenger loading, door times, or destination distribution can produce different results even when the proposed equipment is similar.
Request the inputs and calculation method behind each result before comparing the final figures. A meaningful comparison uses consistent project requirements and identifies any differences in modeled conditions.
How to Evaluate an Elevator Traffic Analysis Report
Use the following checklist to assess whether a report provides sufficient information for equipment selection.
- Building data: Are population, attendance, floor heights, entrances, and intended building use documented?
- Traffic assumptions: Are peak periods, passenger arrival rates, and destination distributions realistic?
- Performance criteria: Are handling capacity, interval, and waiting-time targets clearly defined?
- Equipment configuration: Are quantity, rated capacity, speed, door arrangement, and served floors specified?
- Calculation method: Are formulas, variables, units, and assumptions traceable?
- Simulation quality: Are inputs, scenarios, and model limitations documented?
- Alternative configurations: Are options compared against the same project requirements?
- Building compatibility: Does the proposal fit shaft dimensions, lobby layout, and structural constraints?
- Lifecycle requirements: Are maintenance access, component compatibility, and future modernization considered?
A useful report should show how each proposed configuration performs against the project’s targets and explain the trade-offs between service quality, space, cost, and operating requirements.
Predicted performance remains dependent on the installed system, actual passenger behavior, control settings, and maintenance. A traffic report is a planning tool, not a guarantee of future operating results.
Conclusion
Elevator traffic analysis should evaluate handling capacity, interval, RTT, and actual passenger-flow patterns together. A configuration that meets one target may still require revision if it misses another or conflicts with shaft-space, cost, or operating constraints.
Use transparent assumptions for preliminary calculations and choose more detailed analysis when floor populations, traffic directions, or elevator operations exceed the simplified model’s scope. When comparing proposals, investigate differences in inputs before interpreting differences in predicted performance.
For modernization projects, the evaluation should also account for existing structural limits, equipment compatibility, maintenance requirements, and future building use. These factors help establish whether a proposed configuration is not only adequate on paper but also feasible over its operating life.
Explore EKCNE elevator systems and available products to review elevator system and component categories relevant to your project.
FAQ
What is elevator traffic analysis?
Elevator traffic analysis estimates how an elevator system will perform under defined passenger demand and building conditions. It supports decisions about elevator quantity, capacity, speed, service zones, and dispatching strategy.
How is elevator handling capacity calculated?
In a simplified up-peak model, five-minute handling capacity is estimated from the number of elevators, average passengers carried per trip, and round-trip time. The result depends on the assumed passenger loading and traffic pattern.
What is the difference between elevator interval and waiting time?
Interval is the average time between successive elevator arrivals at a reference floor. Waiting time is the time a passenger waits after registering a hall call. Actual waiting also depends on arrival patterns, queue formation, and dispatching.
How many elevators does a building need?
The required number depends on building population, passenger-flow patterns, floor distribution, car capacity, travel time, and required service levels. Preliminary calculations can screen configurations, while complex buildings may need more detailed analysis.